8 Lateral Patient Positioning Base Preparation
and Imaging Top Installation Prior to proceeding with the setup, refer to Imaging Top Installation and Base Preparation or view the Owner's Manual. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP View Imaging Top Installation Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions The Trios Radiolucent Imaging Top must be positioned such that the patient’s center of gravity lies below the centerline of the Crossbars when the patient is positioned laterally. Failure to do so may make the patient unstable during lateral roll. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions After the patient is transferred to the Trios Radiolucent Imaging Top in a supine position, roll the patient to a lateral position and support the patient until final positioning is achieved. Trios Side Rail Adapter To install the Trios Side Rail Adapter, open the clamp using the black knob and place the Adapter in the desired location with the black knob facing downward. Tighten the knob to secure it in place. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 1 Mounting Components or Accessories Use the Trios Side Rail Adapter when mounting accessories and components such as arm boards. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Clark Socket Slide the Clark Socket onto the Trios Side Rail Adapter. Do not tighten until accessory post is inserted. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 2 Lateral Arm Board Unit Insert the post of the Lateral Arm Board Unit into the Clark Socket, and tighten the Clark Socket to secure the post. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 3 Arm Board Adjustments To adjust the position of the lower arm board so that it supports the lower arm at the same level as the Radiolucent Imaging Top, release the drop handle and slide the arm board into place. Tighten the drop handle. Translate the upper arm board so that it adequately supports the upper arm. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Lateral Positioner Bracket Open the clamp on the Lateral Positioner Bracket; slide the Bracket onto the side rail of the Trios Radiolucent Imaging Top with the black knob facing down. Tighten the black knob to lock. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 4 Lateral Positioner Assembly Insert the Lateral Positioner Assembly into the bracket and rotate the Drop Handle clockwise to tighten and lock into place. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 5 Lateral Positioner Placement The three (3) Rectangular Pads that comprise the Lateral Positioner Set can be placed at the scapula, at the sacrum, and over the pubis to support the patient in the lateral position. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Secure patient with the 60 inch (152 cm) safety strap. Tempur-Pedic^® Medical Pillows Pillows may be used under the patient’s legs or head to assist with final positioning, stability and comfort. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 6 The Lateral Patient Positioning setup is now complete. For more information or questions about this setup or any setup, please refer to the Owner's Manual or contact Mizuho OSI for additional support. Setup Complete