12 IM Tibial Nailing: Using Radiolucent Auxiliary Leg Spar
with Tibia Well Leg Support Base Preparation and
Orthopedic Top Installation Trios Table Base Preparation and Installation Prior to procedure setup, refer to the Trios Table Base Preparation and Installation section and complete the required steps. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP View Orthopedic Top Installation Accessory Clamp Attach Accessory Clamp to the frame near the foot-end with receiver on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 1 Tibia Traction Upright Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 2 Insert the Tibia Traction Upright into the Accessory Clamp from the bottom with receiver facing operative side of table. Traction Unit Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 3 Install the Traction Unit into the Tibia Traction Upright. Foot Plate Attach the foot plate to Traction Unit. The Traction Boot may not be used if an interlocking nail is to be inserted. Apply patient safety strap to table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 4 Center Support Board Install the Center Support and secure with locking knob and Center Support Plug. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 5 Radiolucent Auxiliary Leg Spar Install the Auxiliary Leg Spar to the non-operative side of the table and lock into mount. Ensure the T-Handle on the Leg Spar is facing down. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 6 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Transfer the patient in supine position and secure with patient safety straps. Tibia Support Upright and Tibia Counter Traction Post Install the Tibia Support Upright into the middle of the Center Support Board. Attach Tibia Counter Traction Post and reposition patient on the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 7 Accessory Clamp Attach Accessory Clamp (part not visible) to the Radiolucent Auxiliary Leg Spar. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 8 Tibia Well Leg Support Insert the Tibia Well Leg Support into the Accessory Clamp. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 9 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Place the patient’s foot on the non-operative leg into the Boot Assembly on the Tibia Well Leg Support attached to the Radiolucent Auxiliary Leg Spar. Pad and secure the patient’s foot. Place the patient’s operative foot on the Traction Foot Plate attached to the Traction Unit. Pad and secure the patient’s foot. Universal Side Rail Adaptor and Pivoting Arm Board Mount the Universal Side Rail Adaptor (part not visible) on the non-operative side of the table. Install the Pivoting Arm Board on the Universal Side Rail Adaptor. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 10 Clark Socket and Cross Arm Support Mount a Universal Side Rail Adaptor on the non-operative side of the table at the head-end. Mount a Clark Socket on the Universal Side Rail Adaptor and insert the Cross Arm Support in the Clark Socket and tighten the knob. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 11 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Pad and secure patient’s arms onto the Pivoting Arm Board and Cross Arm Support. The IM Tibial Nailing: Using Radiolucent Auxiliary Leg Spar with Tibia Well Leg Support setup is now complete. For more information or questions about this setup or any setup, please refer to the Owner's Manual or contact Mizuho OSI for additional support. Setup Complete