9 Wilson Frame on Imaging Top Base Preparation
and Imaging Top Installation Prior to proceeding with the setup, refer to Imaging Top Installation and Base Preparation or view the Owner's Manual. Ensure the Imaging Top is positioned at the lowest level on the H-Frame when used with the Wilson Frame. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP View Imaging Top Installation Patient Care Kit Preparation Open the Patient Care Kit and set aside. The ProneView^® Cushion Insert should be opened 60 minutes prior to use, while the GentleTouch^® Face Pillow and Arm Cradles should be opened at least 20 minutes prior to use for complete expansion of the foam. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP ProneView Mirror Place the ProneView Mirror Platform on the Radiolucent Imaging Top towards the Head-End. Ensure the posts of the Mirror Platform are in their lowest position, ready for patient transfer. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 1 ProneView Helmet and Cushion Insert Place the ProneView Cushion Insert into the ProneView Helmet and within the tabs provided at the chin end of the ProneView Helmet. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 2 Head Support Options The GentleTouch Pillow can be used to in place of the ProneView Helmet setup. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP + Universal Side Rail Adapters Attach a Universal Side Rail Adapter on each side of the table towards the Head-End. Ensure the black knob is facing downward, and tighten the knob to secure it in place. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 3 Mounting Components or Accessories Use the Universal Side Rail Adapter when mounting accessories and components such as arm boards. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Pivoting Arm Board Mount a Pivoting Arm Board on the non-patient transfer side. Hold the locking lever of the Pivoting Arm Board in the open position and place over the edge of the Universal Side Rail Adapter. Lower the Arm Board into place and release the lever. Install the second arm board following patient transfer. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 4 Arm Board Positioning To pivot, release the latch by pulling it, and pivot the Arm Board to the desired position. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Hyperextension of the shoulder may cause compression of the brachial plexus resulting in a potential nerve or vascular injury. Failure to ensure proper arm positioning may result in harm to the patient. Wilson Frame Installation
Preparations Enlist the help of a second person and lift the Wilson Plus in the wheeled case into place on the Radiolucent Imaging Top. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Orient the case so that the wheels are facing up and towards the Head-End of the Table, and the handle of the case rests on the table facing the Foot-End. Wilson Frame Center the frame, and remove the case. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 5 Universal Side Rail Adapters Attach an Adapter on each side of the table such that they are aligned with the approximate midpoint of the Wilson Frame. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 6 Safety Strap Attach the two parts of the Safety Strap to the Universal Side Rail Adapters located near the Wilson Frame. Using the Safety Strap, secure the Wilson Frame to the Table. Ensure the placement of the strap will not impede the motion of the pads when the Frame is flexed. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 7 Wilson Frame Positioning
For Patient Transfer The Wilson Frame should be at its lowest position for patient transfer. Insert the Crank Handle into the base of the Wilson Frame. Engage the end of the Crank on the Post and turn counterclockwise to lower the pads to their lowest position. An audible clicking sound will be heard when the lowest position is reached. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Care Kit Application Disengage the pads from the Foot-End Retaining Lip to place the Disposable Patient Care Kit Pad Covers on each pad. To disengage pads, reach under the pad support and lift up at the center of the pad to release from the Retaining Lip. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Care Kit Application Apply the foam cross bar protector over the cross bar at the head end of the frame. This protector will help ensure that the patient does not make accidental contact with the metal cross bar. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Care Kit Application Remove the crank from its storage slot in the base and apply the base cover across the base of the Frame. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Wilson Pad Position While the pads are disengaged from the Foot-End of the Frame, set them to the surgeon’s preferred width, which is usually determined by patient size. The patient’s anatomical landmark for pad placement is the patient’s nipple line, which is usually midline on the pads. To adjust each pad, push and hold the red Lateral Adjustment Release Button located at the Head-End of the frame. Slide the pad supports to the desired location, and release the button to lock into place. Re-engage the pad. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Ensure patient’s anatomical landmarks are aligned with support pads and log roll the patient to a prone position. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Secure patient with the 60 inch (152 cm) safety strap. The Wilson Frame on Imaging Top setup is now complete. For more information or questions about this setup or any setup, please refer to the Owner's Manual or contact Mizuho OSI for additional support. Setup Complete