7 IM Femur Nailing, Lateral Decubitus Position
Unilateral Skeletal Traction Assembly Instructions
& Part Reference Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Advance Control Base Preparation and Installation Prior to procedure set up, refer to the Advance Control Base Preparation and Installation section and complete the required steps. Refer to the Owners Manual section 4 for additional base installation instructions. VIEW NOW CONTINUE WITH SETUP Assembly Instructions
& Part Reference Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Installation of Orthopedic Traction Arc Following Step 1 view the Installation of Traction Arc section and complete the required steps.  Refer to the Owners Manual section 5 for additional Traction Arc installation instructions. VIEW NOW CONTINUE WITH SETUP Assembly Instructions
& Part Reference Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Position the Orthopedic Traction Arc Slide the Traction Arc and the Anatomical Adjustment Roller to the operative side of the table and lock. With the Traction Arc extended to its full length on the non-operative side of the table, slide one Tractor to the end of the Traction Arc on the non-operative side of the table and lock. Slide the operative side Tractor to the mid-position on the Traction Arc and lock. VIEW NOW CONTINUE WITH SETUP Traction Unit Upright Install V or W into the Tractor on the operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP V,W Traction Extension Install X-2 into V or W receiver facing medially. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP X-2 Traction Unit Install P-1 into X-2. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP P-1 90º Pin and Wire Holder Attach T to P-1. Rotate T 90 degrees toward operative side by releasing the Gold Lock Handle. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP T Center Support Board Apply Safety Strap (FF) to table. Install F and secure with locking knob and Center Support Plug. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP FF/F Accessory Clamp Attach (2) AA to the frame near the foot end with receiver on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP AA Leg Board Insert DD into the distal AA. Position at table top height. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP DD Lower Leg Support Insert EE into the proximal AA. Position 6 inches above DD. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP EE Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Transfer the patient to the table in the supine position. With surgical team supporting, position the patient with the non-operative thigh on F. Roll patient into the lateral position; operative leg up. Secure with patient safety strap (FF). Ilium Post & Lateral Perineal Post Insert J and K to the non-operative side F. Rotate the J to adjust K approximately 30 degrees with the elbow toward the foot-end of the table and lock. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP J/K Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Place lower (non-operative) leg on DD and adjust the board position as required, pad, and secure. Position the operative leg in the T with the calf onto EE, pad, and secure. Universal Side Rail Adaptor (XX) and Clark Socket (YY) Mount XX on the non-operative side of the table (two locations). Mount YY to proximal XX. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP XX/YY Pivoting Arm Board Install RR onto distal XX on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP RR Cross Arm Support Install SS onto YY on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP SS Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Pad and secure patient’s arms onto RR and SS. The IM Femur Nailing, Lateral Decubitus Position – Unilateral Skeletal Traction setup is now complete. For more information or questions about this setup or any setup, please refer to the Owner's Manual or contact Mizuho OSI for additional support. Setup Complete